While Whipple broke many rules and records with its record setting S550 supercharger system, holding the title of the most powerful, most advanced supercharger system available, we weren't satisified and decided to build an all new supercharger from the ground up. The stage 2 competition supercharger system is designed for the racer looking to make in the 700-2000 flywheel HP range with the billet roval 150mm throttle body.
The new, direct and port injected supercharger system features the brand new Generation 5 3.8L front feed twin-screw supercharger. Not to be confused with the Gen 3 or 4, this all new supercharger features industry leading efficiency from idle to redline. All new bearings, gears, rotors and housing allow the new supercharger to spin faster, longer and safer while producing more power than any other positive displacement supercharger ever built. The new Gen 5 features an all new 3/4 rotor combination vs previous 3/5, 285 deg helix vs previous 270 deg, new bell mouth inlet, optimized discharge port and increased diameter vs length for higher efficiency.
It also features an all new patent pending triple intercooler design that has even more volume and surface area than the already massive Whipple Cooler that cooled the Ford Cobra Jets and all the record setting S550 Mustangs. Couple this with the industry's leading heat exchanger, water reservoir and intercooler pump, you get more power with lower boost levels and quicker recovery times after aggressive operation.
Every competition SC system features a 6-rib billet idler system and billet spring loaded tensioner, billet idler pulleys and lightweight pocketed supercharger pulley. The 6-rib can easily be upgraded to a 10-rib with the optional 10-rib system. Each system comes with an adjustable idler pulley to allow variance in SC pulleys with minimal belt length changes. The massive 150mm Roval inlet allows for nearly any throttle body to be run, 80mm stock, 132mm or 150mm throttle bodies.
WHIPPLE SUPERCHARGERS S550 EXCLUSIVE FEATURES
-Largest intercooler system on the market, featuring patent pending triple core technology
-Billet 150mm high flow throttle pre-set with factory electronics
-No other upgrades required, just massive power right out of the box
-Front entry Gen 5 W185ax (3.8 liters/3800cc) Whipple twin-screw supercharger that significantly outperforms competitions 2.3L and 2.65L roots-type systems
-Gen 5 supercharger features new 3x4 rotor combination for increased RPM capacity, large diameter for increased airflow and small leak path, increased helix for optimal sealing
-3.8L is 23% larger than 2.65L roots-type allowing lower power draw and lower discharge temps to flow the same amount of air (more power to the rear wheels)
-Oversized Crusher™ 150mm inlet for maximum airflow capacity and minimal rotor cavitation
-Inverted design allows for oversized intercooler core compared to other smaller intercooler cores giving Whipple lower air charge temps which allows more boost and timing to be run on pump gas
-Patent pending triple intercooler technology with massive dual 1" inlet port capacity
-Massive air-to-water aluminum bar-plate intercoolers (over 55% larger than some competition) offer more cooling than any other positive displacement system available, nothing comes close
-Massive oversized aluminum intercooler reservoir (over 2 gallons) holds more than double any competitors IC water system allowing longer more consistent power levels vs. competition
-High flow intercooler pump, nearly double the flow of the standard units others use
-Whipple Superchargers massive oversized intercooled air-bypass system for industry leading reduction of burst knock and incredible fuel economy
-Exclusive 3x4 rotor combo for significant increase in airflow under the curve than less efficient 4x4 roots
-Center discharge port for better cylinder to cylinder distribution then other twin-screws with cobbled together billet adapters and forward facing discharge
-Extra plenum volume below intercooler core for far less pressure drop and better use of the increased surface area of the massive intercooler core
-More boost at the "hit" than any other twin-screw
-Flat torque curve for incredible acceleration
-High flow fuel pump replaces stock pump
-Oversized heat exchanger for incredible intercooler water temps, 150% more volume than competition, standard with every kit
-Fits under factory hood with no modifications
-No cutting or grinding on the engine block
-No cutting or grinding the K-brace
-No internal modifications required
-Kits come complete with all necessary parts and hardware for installation
-Plug and play wiring with male and female connections
-Proven 6-rib belt system with heavy duty spring loaded tensioner and adjustable idler system
-Optional 10-rib belt system with matching 6061 T6 billet pulleys
-OEM quick connect fittings for easy installation
-Complete kits and competition kits are available
-Available in wrinkle black, polish, Ford textured blue or any custom color
Instant boost at the touch of the throttle
3 minute pulley changes
Easy belt changes
Lightweight pocketed 6061 T6 billet aluminum SC pulley
